searching for multi layer pcb design?

Multi layer  PCB Design

What is a Multilayer PCB?

A printed circuit board (PCB) is a thin board “printed” with electrical wires and made from fiber glass or similar material. PCBs are commonly used in computer devices such as motherboards, network interface cards, and RAM chips.multi layer pcb design They are relatively cheap and quite fast. When the PCB is fabricated with several layers placed over one another, it is known as a multilayer PCB. The multiple layers establish a reliable set of predetermined interconnections for the electronic circuits.

There are several techniques that can be used to accomplish this task. Some of these techniques are handicapped by their reliance on a large number of chemical processes to condition the substrate. A large number of chemical processes are needed to activate the through-holes and electrolytic copper plate between the adjacent layers. The general procedure is as follows:

1. Obtaining the material and equipment that you will need, such as drills and electrolytic copper-plating cell.
2. Formatting the copper substrates so that the orientation of each can be uniquely determined. This is sometimes known as patterning and can be done using a variety of methods.
3. Drilling the layers with specific drilling equipment to create holes or vias. These vias are plated with copper to form plated-through holes.
4. Properly cleaning the copper substrates on your board.
5. Electroplating the PCB substrate using acid copper electroplating.
6. Laminating the multilayer board.
Under high pressure and heat, the layers fuse together. The conductors will be separated, and signals and power between layers will be connected. pcb design  This technique ensures that all the layers are drilled and plated first, and then laminated. This can help reduce the number of chemical processes needed to accomplish this difficult task. Multilayer PCBs can have as many as 14 layers. However, this may be quite expensive, and it is more common for PCBs to have either 6 or 8 layers.

A multilayer PCB contains two reference planes and a signal via. The signal via allows a signal to flow through all the planes. A stitching via is connected to one of the planes next to the signal via and serves to reduce the area through which the signal passes through. This is very important as it may assist in reducing noise and cross talk.

Product functionality of the multilayer PCB depends on the interconnection between the layers. Thus it is very critical to be concerned about micro vias and overall HDI.

Multilayer boards can either be rigid or flexible. Rigid multilayer PCB technology can prove to be very expensive because of the expertise required and the expensive drilling equipment. Flexible multilayer PCBs make use of flexible circuits and reduce the size of the end product. pcb design services However, flexible multilayer PCBs must have fewer layers because an increase in the number of layers means a loss in flexibility of those layers.

Advantages of multilayer PCBs include high reliability and uniform wiring. However, the initial costs are higher than that of one-layered PCBs. Also, repairing a multilayer PCB is quite difficult.

Vias

With multi layer design comes the options of using different types of vias to improve your routing density. There are three types of vias – standard, blind, and buried.

Standard vias go through the whole board, and can connect any of the top, bottom or inner layers. These can be wasteful of space on layers which aren’t connected.

“Blind” vias go from the outside surface to one of the inner layers only. The hole does not protrude through the other side of the board. The via is in effect “blind” from the other side of the board.

Image

“Buried” vias only connect two or more inner layers, with no hole being visible on the outside of the board. So the hole is completely buried inside your board.

Blind and buried vias cost more to manufacture than standard vias. But they are very useful, and almost mandatory for very high density designs like those involving Ball Grid Array (BGA) components.

Power Planes

It is good practice to use “power planes” to distribute power across your board. Using power planes can drastically reduce the power wiring inductance and impedance to your components. This can be vital for high speed digital design for instance. It is good design practice to use power planes whenever possible. They can even be used on double sided boards, if most of your signal tracks are on the top layer.

A power plane is basically one solid copper layer of board dedicated to either your Ground or Power rails, or both. Power planes go in the middle layers of your board, usually on the layers closest to the outer surfaces. pcb layout On a 4 layer board with complex power requirements it is common to dedicate one layer to your ground plane, and another layer to your various positive and negative power tracks. Your ground rail is usually your signal reference line, so a ground plane is first preference before a power plane is considered.

Many PCB packages have special Power Plane layers that are designed and laid out in reverse to your other normal tracking layers. high speed pcb design On a normal tracking layer, your board is assumed to be blank, and you then lay down tracks which will become your actual copper tracks. On a power plane however, your board is assumed to be covered with copper. Laying down tracks on a power plane actually removes the copper. This concept can take some getting used to.

 

Advertisements

Leave a Reply

Fill in your details below or click an icon to log in:

WordPress.com Logo

You are commenting using your WordPress.com account. Log Out / Change )

Twitter picture

You are commenting using your Twitter account. Log Out / Change )

Facebook photo

You are commenting using your Facebook account. Log Out / Change )

Google+ photo

You are commenting using your Google+ account. Log Out / Change )

Connecting to %s